I am using it for several Annona spp. and Myrica rubra. I use a concentration of 500-900ppm depending on the size of the seed for 24 hours and use peroxide as well in the mix (1%). Have had fairly good results.
I got this regarding GA3 from the internet;
GA3 Powder 90% is soluble in 70% common rubbing alcohol. Before it can be used is must be turned into a liquid. The amount of Gibberellic acid that needs to be used is very small. Drop the correct amount of powder in a small bottle, then add a few drops of rubbing alcohol. The only reason to use alcohol is to dilute the Gibberellic acid powder. Use just enough alcohol to wet the gibberellic acid powder. If after a couple of minutes you can still see some powder add a few more drops of alcohol. Then just add water to get he right concentration. It is often being said that alcohol will damage plants. Yes, but not in the very low concentration needed to dissolve Gibberellic acid. 90% GA3 powder will not dissolve in water. Once mixed it loses viability within a week, even if refrigerated.
You don't need much of the solution to soak your seeds, just enough for the seeds to fully swell. Most seeds can be soaked in the small poly-bags. Tiny seeds should be folded up in a filter paper for ease of handling when soaking. Larger seeds can be soaked in a pill bottle or small jar.
To know the concentration, replace X and Y, (X mg / Yml) x 1000 = Z ppm
To know the amount of solution to make to get a certain ppm, replace X and Z, (X mg / Z ppm) x 1000 = Y ml
To know the quantity of powder to use, replace Z and Y, (Z ppm x Y ml) / 1000 = X mg
For exemple: 100mg of GA3 in 200ml of water gives you 200ml at 500 ppm (part per million). 100mg of GA3 in 400ml of water gives you 400ml at 250 ppm. 1g of GA3 at 90% concentration will be supplied as a powder in a small ziplock bag, sufficient quantity to make a 2 liters of solution at 500 ppm. You should have enough for a couple of years.
Use strong solution, 500 ppm, on very hard to germinate seeds; and a 250 ppm on seeds that are just hard or slow to start. Seeds enclosed in a hard coat may be submit to a higher concentration, 750-1000 ppm. You can scarify the seeds at first. Soak seeds for 24 hours and at most three days for the ones enclosed in a hard coat. Keep the seeds at room temperature with occasional careful shaking. The seeds may then be sown. Don't use it on easy to start seeds unless you dilute it greatly, like 25-100 ppm, and soak them only for 2-3 hours. Normal, easy-to-sprout seeds will become very elongated and stretched out, then die if GA3 is used on them. Concentrations of about 2 ppm can cause tubers to sprout earlier.
Gibberellic acid can also influence the timing of flowering, flower gender, flower size and increase the number of flowers. If a plant is sufficiently developed, premature flowering may be induced by direct application of GA3 to young plants. Formation of male flowers is generally promoted by concentrations of 10 to 200 ppm, female flowers by concentrations of 200 to 300 ppm. You may have an increase in the number of flowers by direct application of GA3 to young plants, at 25 ppm.
When there is difficulty with fruit set because of incomplete pollination, GA3 may be effectively used to increase fruit set. The resulting fruit maybe partially or entirely seedless.
GA3 applied near the terminal bud of trees may increase the rate of growth by stimulating more or less constant growth during the season. Since GA3 regulates growth, applications of very low concentrations can have a profound effect while too much will have the opposite effect.
Although GA3 is not listed as a poison, the following precautions should be observed. Flush with water any GA3 that may get into the eye. Avoid skin contact if possible and wash away any contact with soap and water. Avoid ingestion of GA3.